How to Cut a Taper on a Table Saw?

If you work in construction sector, or you’re a DIY beginner or professional, you already know the table saw. This is one of the most used tools that DIY enthusiasts and construction workers require.

Though you know the table saw, you may not have the proper idea how it works and how to cut a taper on a table saw.

When it comes to cutting tapered boards, you definitely need the best table saw. Owning a table saw is not everything. You will then need to know the right process about cutting a taper on a table saw. The following guide will cover the method properly.

Why Do You Need a Table Saw?

A table saw can be used in different purposes. The below facts are some reasons that’s why you need a table saw.

For a straight cut on board, you can utilize a common table saw. Cross cuts of board in various sizes can be done with it. To trim woods and give a specific size for different projects, a table saw is simply awesome.

Many best table saws under 1000 can successfully adjust the wood’s angle when cutting. Adjusting the blade’s angle allows you to make perfect angle cuts. Sometimes, you may need to use your skills for ensuring good cuts.

You can also make joints with the use of a table saw. But extra effort and skill might be required.

Also Read: Can I Use a Smaller Blade on My Circular Saw?

Things You Will Need

• A portion of board or plywood.
• Screw and mount block.
• Rockler taper Jig for creating modified and delicate cuts.
• A clamp for secure mounting.
• Blade for making cuts on the board or wood.
• Pencil for measurements and marking.
• A saw for cutting taper.
• A sufficient power source.
• Tape for the correct measurement.

Steps on How to Cut a Taper on a Table Saw

You’ll need to maintain a few steps to cut a taper. Make sure to follow these steps properly to make an ideal cut of a double taper on a table saw. The first part is about using the taper jig on the table saw to cut a long taper.

An Appropriate Base: A section of board can be used as a suitable base. Make sure it has one longer straightedge than other. Making a base for the jig, you can also utilize plywood or same type sheet material. The material should be sturdy to avoid any breaking. Make the base a bit longer than the leg that you aim to taper.

Defining the Blade’s Position: Identify the position where the saw blade will enter and leave the wood. To properly cut on the piece, draw the taper and expand the line. Expand the line toward the end of leg.

Hold tightly the leg with the jig base and the bench. To ensure the utmost cutting legerity, make the taper line properly upright aligned.

The support board will be same as the leg in length. Attach it behind the leg. Use the wood screws to fasten the support piece in the right place on the suitable base.

A Stock Block: Select a stock block that can ideally fit your rockler taper jig. Make sure to attach the stock block to the taper jig and properly position against the leg.

Create Two Blocks: Maintaining similar length and thickness of the leg, construct two mounting blocks. Fasten them behind the support; make sure they’re quite closer to the leg’s end.

Using the Toggle Clamp: Screw the toggle clamps in the blocks. Confirm that the mounting blocks are properly positioned. Tighten them firmly on the leg. The rockler taper jig is ready now after completing these steps.

Arrangement: On the table saw, place the jig. Adjust the blade and make sure that the teeth are ¼ inch above of the upper part of the leg. Keep up the taper jig on rip fence. Check by pulling the jig back that it is not firmly connected to the blade. Finally, lock that rip fence.

Turn on the Saw: Start the table saw. Now, feed your jig toward the rip fence. It is because you need to rip the taper properly. Using your hand, make sure to provide the maximum support to your jig.

This is quite an effortless procedure of cutting tapered or angled parts with the help of a table saw.

Wrap Up

The aforementioned steps are simple to follow. By following these steps, you can perfectly cut a taper on a table saw. The most vital thing you need is your proper attention on the task you’re performing.

I hope the writing has helped you to know how to cut a taper on a table saw. With the help of the steps mentioned above, you will need to use the best table saw that can actually help you. Make sure to buy a user-friendly and affordable saw that you can afford and easily use.

Recommended Read: What Are the Best Saws for Cutting Pallets